@Copyright 1994

All Rights Reserved.

Manual edition 15, August 1994

 

The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.


Trademarks

TB-24P, TB-24R, TB-16P8R is registered trademarks of ADClone Inc., Ltd. IBM PC is a registered trademark of International Business Machines Corporation. Intel is a registered trademark of Intel Corporation. Other product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.


Contents


How to Use This Guide
1. TB-24P
1.1 introduction
1.2 Specifications
1.3 Description
2. TB-24R
2.1 introduction
2.2 Specifications
2.3 Description
3. TB-16P8R
3.1 introduction
3.2 Specifications
3.3 Description
Product Warranty/Service

How to Use This Guide


This manual is designed to help you use the TB-24P/24R/16P8R. The manual describes how to modify various settings on the TB-24P/24R/16P8R card to meet your requirements.

· Chapter 1, "TB-24P : 24 Opto-isolated Digital Inputs Terminal Board, " gives an overview of the TB-24P's features. description, and specifications.

· Chapter 2, "TB-24R : 24 Relay Outputs Terminal Board, " gives an overview of the TB-24R's features. description, and specifications.

· Chapter 3,"TB-16P8R ; 16 Opto-isolated Digital Inputs & 8 Relay Outputs Terminal Board," gives an overview of the TB-16P8R features. description, and specifications



1. TB-24P : 24 Opto-isolated Digital Inputs Terminal Board




1.1 Introductions:

TB - 24P is an input extension board with 24 isolated photo couplers. CN1, CN2, CN3 and CN4 are terminal blocks to connect with external devices. CN5 is a 50 pins connector to connect with opto-22 compatible connetor, such as ACL-724, ACL-722, PET-48DIO, etc. All input ports are with LED indicators.


1.2 Specifications:


1.3 Descriptions:

TB-24P has 5 connectors and 24 LEDs. The following Figure shows their placement on TB-24P.

TB-24P has 24 LEDs to indicate input status, the LED mapping and logic define shows as following table.

LED No.

Indication Display

Color of LED

Channel

LED 0

PA0

GREEN

CH0

|

|

|

|

LED 7

PA7

GREEN

CH7

LED8

PB0

YELLOW

CH8

|

|

|

|

LED 15

PB7

YELLOW

CH15

LED 16

PC0

RED

CH16

|

|

|

|

LED 23

PC7

RED

CH23

LED mapping table

Logic "1" LED " ON"
Logic "0" LED "OFF"
Logic define

Each input channel can connect with opto-22 compatible Digital I/O board, such as ACL-722, PET-48DIO, etc. directly or through photo coupler, and the upper of each photo coupler has a jumper to select .

Each input port has two mini jumpers for setting.



Each input channel has two terminal blocks. The terminal block pins' define as following figure.

CH
12		 CH
14		 CH
16		 CH
18		 CH
20		 CH
22
V+ V- V+ V- V+ V- V+ V- V+ V- V+ V-

CN2
CH
13		 CH
15		 CH
17		 CH
19		 CH
21		 CH
23
V+ V- V+ V- V+ V- V+ V- V+ V- V+ V-

CN3
CH
0		 CH
2		 CH
4		 CH
6		 CH
8		 CH
10
V+ V- V+ V- V+ V- V+ V- V+ V- V+ V-

CN4
CH
1		 CH
3		 CH
5		 CH
7		 CH
9		 CH
11
V+ V- V+ V- V+ V- V+ V- V+ V- V+ V-

The CN5 is a opto-22 compatible connector, its pin assignment shows as following figure.


CN5 pins define figure



2. TB-24R : 24 Relay Outputs Terminal Board





2.1 Introduction

TB - 24R is an output extension board with 24 relays. CN1, CN2, CN3 and CN4 are terminal blocks to connect with external devices. CN5 is to connect with external + 12V power source. CN6 is to connect the opto-22 compatible connector, such as ACL-722, ACL-724, PET-48DIO, etc.


2.2 Specification

Max. switching power 60 W, 125 VA
Max. switching voltage 220 V DC, 250 V AC
Max. switching current 2 A DC, AC
Max. carrying current 3 A DC, AC
UL/CSA rating 0.6 A 125 V AC
UL/CSA rating 0.6 A 110 V DC
UL/CSA rating 2 A 30 V DC
Coil voltage : 12 V DC


2.3 Description

TB-24R has six connectors. The figure as below is placement of these connector.

The 24 LEDs are indicators of output ports. The mapping of LED and Logic define are showing as table.

LED No.

Indication Display

Color of LED

Channel

LED0

PA0

GREEN

CH0

|

|

|

|

LED7

PA7

GREEN

CH7

LED8

PB0

YELLOW

CH8

|

|

|

|

LED15

PB7

YELLOW

CH15

LED16

PC0

RED

CH16

|

|

|

|

LED23

PC7

RED

CH23

LEDs Mapping Table



Logic "1" LED " ON"
Logic "0" LED "OFF"
Logic Define Table

CN1, CN2, CN3 and CN4 are terminal blocks to connect with external device.


Each output channel has three terminal blocks to connect, the define is showing as figure.


Channel No.
Common Normal close Normal open

Terminal block define of each channel



The relationship of channel No. and CN1, CN2, CN3, CN4 are showing as figure.

CH12 CH14 CH16 CH18 CH20 CH22
CH13 CH15 CH17 CH19 CH21 CH23
CN2

CN3

CH0 CH2 CH4 CH6 CH8 CH10
CH1 CH3 CH5 CH7 CH9 CH11


CN4

The relationship of channel and CN1,CN2,CN3,CN4

The CN5 is to connect with external +12V power source. Figure shows CN5 connecting.


The CN6 is to connect with opto-22 compatible connector, such as ACL-722, ACL-724, or PET-48DIO, etc. Its pin assignment is defined as following figure.

3. TB-16P8R : 16 Opto-isolated Inputs & 8 Relay Outputs Terminal Board




3.1 Introduction

The TB-16P8R is input / output extension board with 16 input ports and 8 output ports. All input ports are with photo couplers, and all outputs are with relays. Terminal blocks on TB-16P8R are to connect with external devices. Photo coupler of input port is able to by pass the same as TB-24P.


3.2 Specification

Max. switching power 60 W, 125 VA
Max. switching voltage 220 V DC, 250 V AC
Max. switching current 2 A DC, AC
Max. carrying current 3 A DC, AC
UL/CSA rating 0.6 A 125 V AC
UL/CSA rating 0.6 A 110 V DC
UL/CSA rating 2 A 30 V DC

Coil voltage: 12 V DC


3.3 Descripition

TB-16P8R has 6 connectors and 24 LEDs. The following Figure shows teeir placement on TB-16P8R.




TB-16P8R Outline


The input port of TB-16P8R is same as TB-24P. Each input channel has two terminal blocks. The pins' define of CN1, CN2 is showing as following figure.

The output port of TB-16P8R is same as TB-24R. Each output channel has three terminal blocks.

The relationship of channel and CN3, CN4 is showing as table.

The relationship of LED, channel and output port is showing as table.

The CN5 is to connect external +12 V. Figure shows connecting.

The CN6 is connector to connect with opto-22 compatible connector. Figure shows CN6 pins' define.

The 8 relay output ports (8R) connects with PET-48DIO port A through CN6,and 16 photo coupler input ports (16p) connects with PET-48DIO port B,C through CN6.

Product Warranty/Service




Seller warrants that equipment furnished will be free form defects in material and workmanship for a period of one year from the confirmed date of purchase of the original buyer and that upon written notice of any such defect, Seller will, at its option, repair or replace the defective item under the terms of this warranty, subject to the provisions and specific exclusions listed herein.

This warranty shall not apply to equipment that has been previously repaired or altered outside our plant in any way as to, in the judgment of the manufacturer, affect its reliability. Nor will it apply if the equipment has been used in a manner exceeding its specifications or if the serial number has been removed.

Seller does not assume any liability for consequential damages as a result from our products uses, and in any event our liability shall not exceed the original selling price of the equipment.

The equipment warranty shall constitute the sole and exclusive remedy of any Buyer of Seller 9273 equipment and the sole and exclusive liability of the Seller, its successors or assigns, in connection with equipment purchased and in lieu of all other warranties expressed implied or statutory, including, but not limited to, any implied warranty of merchant ability or fitness and all other obligations or liabilities of seller, its successors or assigns.

The equipment must be returned postage-prepaid. Package it securely and insure it. You will be charged for parts and labor if you lack proof of date of purchase, or if the warranty period is expired.



©1995 Circuit Specialists, Inc.